{"product_id":"600x600x10mm-tile-backer-boards-xps-water-resistant-pack-of-6","title":"Tile Backer Board 600x600x10mm — XPS Water-Resistant Wall \u0026 Floor Board (Box of 6)","description":"\u003cp\u003e\u003cstrong\u003eA water-resistant backer board for tiled walls and floors\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eA closed-cell extruded polystyrene core with fibreglass mesh embedded in a polymer-modified cement coating on both faces. It absorbs no more than 1.2% water by volume. Fix it, tape the joints, waterproof it and tile.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eChoosing the right thickness — read this first\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThickness is not a preference. It is decided by what you are fixing to. A board too thin for the stud spacing will flex under the weight of the tiles. Measure the stud centres, from the centre of one stud to the centre of the next, before you buy.\u003c\/p\u003e\n\n\u003cp\u003eFor these 10mm boards, studs are at 300mm centres or less.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eFixing to a frame\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eAll board edges, including horizontal joints between boards, must be fully supported on framing.\u003c\/li\u003e\n\t\u003cli\u003eMinimum 5 screws and washers per square metre, galvanised or stainless steel.\u003c\/li\u003e\n\t\u003cli\u003eKeep fixings at least 30 mm from the edge of the board.\u003c\/li\u003e\n\t\u003cli\u003eWhere two boards meet, preferably add a dedicated nogging or stud behind the joint. If both boards share a single 45 mm stud or nogging, fix each board at least 15 mm from its edge, plus one fixing on the joint line.\u003c\/li\u003e\n\t\u003cli\u003eTighten until the washer sits flush. Do not overtighten.\u003c\/li\u003e\n\t\u003cli\u003eStagger the board joints.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eBonding to a solid substrate\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eThe substrate must be solid, load-bearing, non-deformable, clean, dry and free from dust and grease.\u003c\/li\u003e\n\t\u003cli\u003ePrime absorbent and smooth non-absorbent surfaces. Any commercial acrylic or SBR tile primer compatible with cementitious coatings will do.\u003c\/li\u003e\n\t\u003cli\u003eComb cement-based flexible adhesive over the whole face of the board, at least 6 mm thick.\u003c\/li\u003e\n\t\u003cli\u003eSpot bonding on adhesive dabs needs 20 mm board or thicker.\u003c\/li\u003e\n\t\u003cli\u003eWhere boards are dowelled into masonry, each dowel must penetrate the load-bearing substrate by at least 35 mm.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eOn floors\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eSuitable for floors as well as walls.\u003c\/li\u003e\n\t\u003cli\u003eOn timber floors, these 10mm board is the recommended thickness. The subfloor must be secure.\u003c\/li\u003e\n\t\u003cli\u003eMinimum timber substrate: wood-based panels ≥ 16mm, plywood ≥ 16mm, floorboards ≥ 21mm.\u003c\/li\u003e\n\t\u003cli\u003eOn timber floors, bond the board with full-surface cement-based flexible adhesive, plus screws and washers, minimum 5 per square metre.\u003c\/li\u003e\n\t\u003cli\u003eScrews must penetrate the timber by at least 20mm. On a 16 mm plywood or wood-based panel floor, the screws must reach the joists.\u003c\/li\u003e\n\t\u003cli\u003eNew concrete floors must cure and be primed before the boards go down.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eUnder underfloor heating\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThe boards can be installed beneath electric or hydronic underfloor heating. They must not be laid on top of an active heated screed. For electric heating, or any continuous area over 20m², alkali-resistant glass fibre mesh must be embedded over the board surface in thin-set adhesive — 160 g\/m² mesh with a C2 polymer-modified adhesive.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eJoints, waterproofing and tiling\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eThe board is a water-resistant substrate. It is not a waterproofing membrane. Tape and seal every board joint and internal corner before waterproofing, using glass fibre mesh joint tape. In a shower, bath surround or any wet area you must then apply a waterproofing membrane to AS 3740 before tiling. Polyurethane, acrylic, SBR and polymer-modified cementitious liquid membranes are compatible. Do not use unrefined solvent-based bitumen or high-solvent adhesives over the coating. Tile with a cement-based flexible adhesive — not ready-mixed, not solvent-based. Form all wall-to-floor junctions and internal corners as flexible expansion joints, not grout.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eLimits and handling\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eMaximum tile weight 62kg per square metre. Tiles at least 100 × 100mm and at least 7mm thick.\u003c\/li\u003e\n\t\u003cli\u003eDo not fix basins, toilet pans, grab rails or folding seats to the board. Fix those to the wall framing or to a purpose-built frame.\u003c\/li\u003e\n\t\u003cli\u003eCut with a fine-toothed saw, or score with a sharp knife against a straight edge and snap.\u003c\/li\u003e\n\t\u003cli\u003eStore flat, dry and out of direct sunlight. Do not use solvent-containing products on the board.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eSpecifications:\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cul\u003e\n\t\u003cli\u003eSheet size: 600 × 600mm\u003c\/li\u003e\n\t\u003cli\u003eThickness: 10mm\u003c\/li\u003e\n\t\u003cli\u003eSold as: Box of 6 sheets\u003c\/li\u003e\n\t\u003cli\u003eSuitable for: Full-surface bonding to a solid surface, floors, or studs at 300mm centres or less\u003c\/li\u003e\n\t\u003cli\u003eCoverage per sheet: 0.36m²\u003c\/li\u003e\n\t\u003cli\u003eCoverage per box of 6: 2.16m²\u003c\/li\u003e\n\t\u003cli\u003eThermal resistance (R-value): 0.21 m²K\/W\u003c\/li\u003e\n\t\u003cli\u003eCore: Closed-cell extruded polystyrene, 33 kg\/m³\u003c\/li\u003e\n\t\u003cli\u003eFace: Fibreglass mesh in polymer-modified cement coating\u003c\/li\u003e\n\t\u003cli\u003eWater absorption: Not more than 1.2% by volume\u003c\/li\u003e\n\t\u003cli\u003eCompressive strength: ≥ 300 kPa\u003c\/li\u003e\n\t\u003cli\u003eMaximum tile weight: 62kg per square metre\u003c\/li\u003e\n\t\u003cli\u003eMinimum tile size: 100 × 100mm, at least 7mm thick\u003c\/li\u003e\n\t\u003cli\u003eMinimum fixings: 5 screws and washers per square metre, at least 30mm from the edge (15 mm where two boards share one stud or nogging)\u003c\/li\u003e\n\u003c\/ul\u003e\n","brand":"Della Francesca","offers":[{"title":"Default Title","offer_id":68023931339117,"sku":"JIT-TBB10-6x6","price":234.95,"currency_code":"NZD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0576\/3661\/8423\/files\/30986034a46db676848b2954adce5e11.png?v=1794917169","url":"https:\/\/factoryfast.co.nz\/products\/600x600x10mm-tile-backer-boards-xps-water-resistant-pack-of-6","provider":"FactoryFast.co.nz","version":"1.0","type":"link"}