Tile Backer Board 600x600x10mm — XPS Water-Resistant Wall & Floor Board (Box of 6)
Available with other options:
Product Description
A water-resistant backer board for tiled walls and floors
A closed-cell extruded polystyrene core with fibreglass mesh embedded in a polymer-modified cement coating on both faces. It absorbs no more than 1.2% water by volume. Fix it, tape the joints, waterproof it and tile.
Choosing the right thickness — read this first
Thickness is not a preference. It is decided by what you are fixing to. A board too thin for the stud spacing will flex under the weight of the tiles. Measure the stud centres, from the centre of one stud to the centre of the next, before you buy.
For these 10mm boards, studs are at 300mm centres or less.
Fixing to a frame
- All board edges, including horizontal joints between boards, must be fully supported on framing.
- Minimum 5 screws and washers per square metre, galvanised or stainless steel.
- Keep fixings at least 30 mm from the edge of the board.
- Where two boards meet, preferably add a dedicated nogging or stud behind the joint. If both boards share a single 45 mm stud or nogging, fix each board at least 15 mm from its edge, plus one fixing on the joint line.
- Tighten until the washer sits flush. Do not overtighten.
- Stagger the board joints.
Bonding to a solid substrate
- The substrate must be solid, load-bearing, non-deformable, clean, dry and free from dust and grease.
- Prime absorbent and smooth non-absorbent surfaces. Any commercial acrylic or SBR tile primer compatible with cementitious coatings will do.
- Comb cement-based flexible adhesive over the whole face of the board, at least 6 mm thick.
- Spot bonding on adhesive dabs needs 20 mm board or thicker.
- Where boards are dowelled into masonry, each dowel must penetrate the load-bearing substrate by at least 35 mm.
On floors
- Suitable for floors as well as walls.
- On timber floors, these 10mm board is the recommended thickness. The subfloor must be secure.
- Minimum timber substrate: wood-based panels ≥ 16mm, plywood ≥ 16mm, floorboards ≥ 21mm.
- On timber floors, bond the board with full-surface cement-based flexible adhesive, plus screws and washers, minimum 5 per square metre.
- Screws must penetrate the timber by at least 20mm. On a 16 mm plywood or wood-based panel floor, the screws must reach the joists.
- New concrete floors must cure and be primed before the boards go down.
Under underfloor heating
The boards can be installed beneath electric or hydronic underfloor heating. They must not be laid on top of an active heated screed. For electric heating, or any continuous area over 20m², alkali-resistant glass fibre mesh must be embedded over the board surface in thin-set adhesive — 160 g/m² mesh with a C2 polymer-modified adhesive.
Joints, waterproofing and tiling
The board is a water-resistant substrate. It is not a waterproofing membrane. Tape and seal every board joint and internal corner before waterproofing, using glass fibre mesh joint tape. In a shower, bath surround or any wet area you must then apply a waterproofing membrane to AS 3740 before tiling. Polyurethane, acrylic, SBR and polymer-modified cementitious liquid membranes are compatible. Do not use unrefined solvent-based bitumen or high-solvent adhesives over the coating. Tile with a cement-based flexible adhesive — not ready-mixed, not solvent-based. Form all wall-to-floor junctions and internal corners as flexible expansion joints, not grout.
Limits and handling
- Maximum tile weight 62kg per square metre. Tiles at least 100 × 100mm and at least 7mm thick.
- Do not fix basins, toilet pans, grab rails or folding seats to the board. Fix those to the wall framing or to a purpose-built frame.
- Cut with a fine-toothed saw, or score with a sharp knife against a straight edge and snap.
- Store flat, dry and out of direct sunlight. Do not use solvent-containing products on the board.
Specifications:
- Sheet size: 600 × 600mm
- Thickness: 10mm
- Sold as: Box of 6 sheets
- Suitable for: Full-surface bonding to a solid surface, floors, or studs at 300mm centres or less
- Coverage per sheet: 0.36m²
- Coverage per box of 6: 2.16m²
- Thermal resistance (R-value): 0.21 m²K/W
- Core: Closed-cell extruded polystyrene, 33 kg/m³
- Face: Fibreglass mesh in polymer-modified cement coating
- Water absorption: Not more than 1.2% by volume
- Compressive strength: ≥ 300 kPa
- Maximum tile weight: 62kg per square metre
- Minimum tile size: 100 × 100mm, at least 7mm thick
- Minimum fixings: 5 screws and washers per square metre, at least 30mm from the edge (15 mm where two boards share one stud or nogging)
We accept payment via:
FactoryFast.co.nz endeavours to provide our shoppers with a pleasant online shopping experience.
For warranty and returns information and policies please refer to our Terms and Conditions.
The product listed above shows a general product picture from the product manufacturer which may vary slightly to what is actually received therefore, reported cases of minor variations and differences to what was shown will not be covered by warranty.
-- rebecca QLD
I have recommended the tile backer board to other mosaic artists. It is easy to use! I sketch the shape onto the board then cut it out using a jigsaw or craft knife.
-- Julie VIC
I was happy with the ease of ordering, speed of delivery and the communication that the product was on the way. Good product too, which I will buy from you again.
-- Catherine QLD
Good service
-- rose NSW
Was pleasantly surprised by service and timely delivery
-- Ali SA
Already recommended to several friends
-- Julie SA
Prompt delivery
-- Julie QLD